Author Topic: This Dns clinet error problem haunts me. Is there a real fix? (Read 73453 times)

jraju · « **Reply #25 on:** February 11, 2018, 04:55:47 am »

Hi, Thanks . But selecting the specified also does not permit me to change to dhcp. Even i tried for bridged to test, whether it is giving a chance to select. I do not know anything about wan ip settings in the configuration.
Thanks anyway for giving me a clue to try, samson

Samson · « **Reply #26 on:** February 11, 2018, 05:07:03 am »

Have you tried Boggin's suggested alternative DNS servers in his previous post? Or try OpenDNS ( I use these)...

208.67.222.222

208.67.220.220

Boggin · « **Reply #27 on:** February 11, 2018, 08:18:29 am »

What other options from Bridged do you get when you expand the Channel Mode dropdown ?

Does the same happen on the laptop if you disable wireless on that and wire it up ?

I wonder if it's worth setting the desktop computer up with a static IP address.

You would need to see what the DHCP range the router is using and if it covers from 192.168.1.1 to 192.168.1.254 then you will need to reduce that to say 192.168.1.199 and then you could assign it as say 192.168.1.200

It would need to be outside of the DHCP range to avoid an IP conflict.

Samson · « **Reply #28 on:** February 11, 2018, 08:59:14 am »

Quote from: Boggin on February 11, 2018, 08:18:29 am

Does the same happen on the laptop if you disable wireless on that and wire it up ?

Indeed, from memory the laptop is XP SP3? which, unless it has been added, does not by default support IPv6, only IPv4. I have seen in some forums similar problems to J's resolved by disabling IPv6 in the network adapter's properties. YMMV.

See method 2 here to disable IPv6 on the Win 7 machine and more info on the error.
https://social.technet.microsoft.com/wiki/contents/articles/3336.event-id-1014-microsoft-windows-dns-client.aspx

Boggin · « **Reply #29 on:** February 11, 2018, 09:31:52 am »

While I've never experienced any problems with IPv6 enabled, I always uncheck that box on my laptops as it has been known to cause connectivity problems, but don't recall J's problem being one of them.

One other thing I always do on my Win 7 laptop is to disable the MS Virtual adapter as you only need it if using a VPN.

To do that, from an admin cmd prompt enter -

netsh wlan set hostednetwork mode=disallow

To reinstate it, change disallow to allow

jraju · « **Reply #30 on:** February 12, 2018, 04:14:51 am »

Hi, Sorry for lae reply.
Even after wiping out all, and reinstall windows, i got some 1006 event id errors. I wasa then having only one dns server for testing google dns 8.8.8.8. But when i enabled dhcp, by trying another terracom, my old modem, the actual dns server shown was some that i did not configured in the router. The router had the isp address of course, but the actual dns servers were shown as one top, opendns and the next as google dns. I do not know, how those things come about.
There was no internet, even when all lights are ok. I was getting various error messages , like investigate router or modem,your modem is experiencing connectivity issues, the dns server is not responding, and always got, windows could not automatically detect the network proxy server settings, etc.
I tried google dns and then the connection was somewhat smooth.
I got the internet and the problem gone. But on verifying the event viewer, i found dhcp,dns client errors.
Today also i experienced error id 1006, which i enclose for ready reference.
How even after complete wipe and reinstall , these errors are happening , i do not know.
I still probe, how i got the opendns and google dns server as the actual servers, while i enabled dhcp from my ISP.
There are more than just connectivity in network problems.
I already tried bOggins 3rd level servers, but the problem persisted.
Just with heavy heart, i had to wipe out the total data.
There the suggestion of tb expansion hdd came to my help. I just copied the othe drives and necessary files before opting reinstall of windows.
As already said, changing the auto to specific does not make any difference.
First let me try boggins 3 level ips now .

Boggin · « **Reply #31 on:** February 12, 2018, 06:16:33 am »

Have a read through this article to see if it will resolve the 1014 and 1006 warnings - https://social.technet.microsoft.com/wiki/contents/articles/3336.event-id-1014-microsoft-windows-dns-client.aspx?ranMID=24542&ranEAID=TnL5HPStwNw&ranSiteID=TnL5HPStwNw-i.2RabxXCukVHDUbhImoDg&tduid=(57d8a42b1063dd589f6ff96f5a0894b5)(256380)(2459594)(TnL5HPStwNw-i.2RabxXCukVHDUbhImoDg)()&ranMID=24542&ranEAID=TnL5HPStwNw&ranSiteID=TnL5HPStwNw-i.2RabxXCukVHDUbhImoDg&tduid=(57d8a42b1063dd589f6ff96f5a0894b5)(256380)(2459594)(TnL5HPStwNw-i.2RabxXCukVHDUbhImoDg)()

If you are the only one who had access to that other router then you must have changed the DNS settings at some time as the default is auto which would use your ISP's.

If you have changed to specific DNS settings in the router and then use different ones in the computer, that can cause connectivity issues.

If you want the computer to use specific DNS servers then the router should be set at default and vice versa where you have set the router to specific DNS servers, the computer should be set to auto.

As you have more than one machine, then they should both be set the same.

You haven't said if you have checked to see if you are getting the same error on the laptop - can you check that ?

jraju · « **Reply #32 on:** February 12, 2018, 10:13:19 pm »

Hi, The dns warning and internet light goes off along with dsl still exists.
In one other thread, you have said, i remember, that if i set the dns in the router, then I need not change the dns server in other devices. i do not remember the thread. So, i just enable dhcp or any specific dns server in the router itself.
What is the 1006 event id, where i get, the incorrect configuration of dns server. I do not know. In the mean time, i will also check with dlink support, if there is anything wrong in my configuration.
Yesterday, you have given me a link. i will also look at that.
Those settings i already tried, but let me know, should those commands be tried on every log on. Or is it a one time change?
But i think, that did not work in my case.

Boggin · « **Reply #33 on:** February 13, 2018, 01:27:08 am »

Those cmds for the 1006 error are a one off.

Have you unchecked the box for TCP/IPv6 in the computer or executed that netsh hostednetwork cmd to see if they make any difference.

In the opening lines of your last post, do they refer to the laptop when you disabled wireless and wired up as I'd suggested ?

jraju · « **Reply #34 on:** February 13, 2018, 01:33:26 am »

Hi, I suppose, that after getting the clarification, i would have issued host commands.
But does the wireless connection has anything to do with the modem, except that it fetches the wifi?
I did see the internal ips , it is getting when connected. Is it that when your pc starts, it has to get the ip from dhcp, and hence it is totally emptying the total ip table and then getting the fresh ips for all the connected device once again to get disconnected or reconnected?
Did you check at your end?
Normally, when the dsl line is ok, then the internet should not cut off, when login or logout. Is it correct?
please

Boggin · « **Reply #35 on:** February 13, 2018, 02:02:36 am »

Yes, your router is broadcasting a wireless signal all of the time and DHCP will assign an IP address to each device as it is switched on.

On mine, I can have a machine Ethernet connected but the Ethernet light on the router will not come on until that machine has been switched on and assigned a DHCP IP address - all other lights remain on and just the Ethernet light will go out when I switch that machine off.

My broadband connection will remain intact.

You don't seem to have had much joy from your ISP for setting up the router - D-Link may help but ISPs may have their own particular settings which are specific to them.

Yours is the first router I've seen using WAN Bridged - was that a default setting or what your ISP told you to set it up as ?

Boggin · « **Reply #36 on:** February 13, 2018, 03:53:07 am »

I've just been looking in my ISP supplied Fibre router and it does list a WAN IP but it's for my external IP address.

It's a HG635 and doesn't appear to have a Bridging mode.

The Operating Mode is set to Auto but it gives a choice of WAN or DSL.

jraju · « **Reply #37 on:** February 13, 2018, 05:13:14 am »

Hi, It is not in bridged mode. It is in PPPoe mode, that is connection thro cable thro telephone.
What you see in the picture is default. The actual is at the bottom, where the configured mode is shown. I checked and it is in pppoe mode only. Really i do not know, what is wan ip being fixed.
I will go through all the commands starting with your host command. If the problem is fixed, i will inform you immediately.. Pl see post 20 and 21
Pl also see this
C:\Windows\system32>netsh wlan set hostednetwork mode=disallow
The Wireless AutoConfig Service (wlansvc) is not running.

C:\Windows\system32>

jraju · « **Reply #38 on:** February 13, 2018, 11:01:37 pm »

Hi, Boggins, See this router page, where all the information on dhcp server is available including the pool.
What is dns relay, is it different from dchp server. The default is given. I think, that there is no need to change anything there.
But i have a doubt, that there is a default server name called domain.name.
I do not have any domain. The computer properties list as workgroup only.
please your ideas.
Morever, i have attempted all the repairs in the link. But still, i am experiencing a re connection on log on. The dsl goes out and come back leaving some minutes without internet access.
But the name resolution for domain name timed out, gives some other domain or com name, now
please

jraju · « **Reply #39 on:** February 13, 2018, 11:05:14 pm »

Hi, I forgo to attach the router page as said in the previous post
i could edit a post, but could not have other options if i modify, lilke adding enclosure, or bold , italics etc.
Am i missing something here

Boggin · « **Reply #40 on:** February 14, 2018, 12:40:32 am »

You will need to change that .254 down to say .199 and then assign the pc with a static IP address above .199

jraju · « **Reply #41 on:** February 14, 2018, 02:19:55 am »

Strange, boggins , weird.
Please say what is your primary dns suffic in the computer properties standard, where you have the computer name domain workgroup menu etc. When i click more options, by chance, i get one blank field as primary dns suffic name left default as blank.
I just entered the computer name in it and reboot it as required,
there was no blinking or connection loss during the booting.
What is this blank to do with the error message is not known.
Should it be filled. But , i did not get alert to fill this.
anyhow, what this primary dns suffix, can i give any name? or is a ploy to watch browsing history by ISP or not. I do not see the menu before this.
can i give any name , what purpose, this name to be filled. Can i leave it as blank. pl boggins.

Boggin · « **Reply #42 on:** February 14, 2018, 02:28:14 am »

My Primary DNS Suffix is also blank - this will be default.

jraju · « **Reply #43 on:** February 14, 2018, 02:43:05 am »

Hi, I tried for the second restart,and there is no internet cut as was previous.
What is thiss? I have not gone to the menu at all.
Now, ipconfig a/all list like this
icrosoft Windows [Version 6.1.7601]

Windows IP Configuration

Host Name . . . . . . . . . . . . : sarochan
Primary Dns Suffix . . . . . . . : sarochan
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : sarochan
domain.name

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . : domain.name
Description . . . . . . . . . . . : Realtek PCIe FE Family Controller
Physical Address. . . . . . . . . : xxxxxxxxxxx
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Wednesday, February 14, 2018 4:06:19 PM
Lease Expires . . . . . . . . . . : Thursday, February 15, 2018 4:06:19 PM
Default Gateway . . . . . . . . . : 192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.1.1
NetBIOS over Tcpip. . . . . . . . : Enabled

C:\Windows\system32>

Boggin · « **Reply #44 on:** February 14, 2018, 02:49:20 am »

I don't know - the Host Name is usually the name of the computer and somehow that has created a Domain for you.

jraju · « **Reply #45 on:** February 14, 2018, 04:35:25 am »

Hi, Boggins, that fix is not a permanent one and it is a change call a fluke occurances.
Now i have the same problem of disconnecting. I could name anything in the field change and nothing works. It is this error,
Name resolution for the name _ldap._tcp.dc._msdcs.domain.name timed out after none of the configured DNS servers responded.

Samson · « **Reply #46 on:** February 15, 2018, 09:57:59 am »

Quote from: jraju on February 14, 2018, 02:19:55 am

When i click more options, by chance, i get one blank field as primary dns suffic name left default as blank.
I just entered the computer name in it and reboot it as required,
there was no blinking or connection loss during the booting.
What is this blank to do with the error message is not known.
Should it be filled. But , i did not get alert to fill this.
anyhow, what this primary dns suffix, can i give any name? or is a ploy to watch browsing history by ISP or not. I do not see the menu before this.
can i give any name , what purpose, this name to be filled. Can i leave it as blank. pl boggins.

J, Are you talking about the Network Adapter settings?....You should not enter any name here, this may be why it is appearing that you are a member of a domain.

Compare with mine, attached. Those are OpenDNS entries, yours may be different but everything else should be the same.

jraju · « **Reply #47 on:** February 15, 2018, 09:47:24 pm »

Hi, Samson, No not in network properties
In computer properties, if you click on settings and then select computer tab, and then more, you will get a Primary Dns suffix , which by default is blank.. I tried give a name. But that was not successful as it turned out to be fluke occurrences as i have pointed out in my earlier post.
i have not given a domain name in the computer, but in the dlink router settings in the dhcp server settings, it gives a name as domain.name.
Can i change it? Why it is giving a domain name.

Moreover, I did not change dns server in the outer computer settings , but in the router itself, as i have to do it on all devices if i select dns server in computer settings.
Can i write the same dns server name in the blank spaces in your diagram?

Samson · « **Reply #48 on:** February 16, 2018, 12:31:27 am »

Enter and save whatever DNS server addresses that you have chosen to use in the red box of the attached screen shot...set the Domain name box "blank". Then run ipconfig /flushdns, reboot and report back.

Also show your equivalent screenshot for network adapter settings, TCP/IP advanced DNS, like mine above.

jraju · « **Reply #49 on:** February 16, 2018, 01:25:17 am »

Hi, Samson, If i enter the dns server shown in the router. as configured, it is not accepting rejecting it as invalid characters alert.
If i delete the name and leave it blank, also , it gives the same error message
I enclose the network advanced properties